设为首页|加入收藏

• 首 页
• 美军标 MIL
• 国际标准
• 协会标准
• 国内标准
• 论 坛

HB 6144-1988 压接型插头座电线压接规范

上一篇: HB 6146-1988 航空高精度液压过滤器 通用技术条件
下一篇: HB 6147-1988 小螺旋窄带卡箍

标准名称：	烤烟托盘育苗技术规程
发布部门：	陕西省质量技术监督局
发布日期：	2007-07-24
实施日期：	2007-07-24
首发日期：
作废日期：
出版日期：	2007-07-24

没有内容

没有内容

没有内容

没有内容

Product Code:SAE J1442
Title:High-Strength, Hot-Rolled Steel Bars
Issuing Committee:Carbon And Alloy Steels Committee
Scope: This SAE Recommended Practice covers two levels of high strength structural low-alloy steel bars having minimum Yield Points of 345 MPa (50 ksi) and 450 MPa (65 ksi).The two strength levels are 345 and 450 MPa or 50 and 65 ksi minimum yield point. Different chemical compositions are used to achieve the specified mechanical properties. In some cases there are significant differences in chemical composition for the same strength level, depending on the fabricating requirements.It should be noted that although the mechanical properties for a steel grade sourced from different suppliers may be the same, the chemical composition may vary significantly. The fabricator should be aware that certain compositional differences may effect the forming, welding, and/or service requirements of the material. It is therefore recommended that the fabricator consult with the producer to understand the effect of chemical composition.The products within the scope of this document include bars of the following types and sizes:Rounds, squares, and hexagons of all sizes (cut length only), flats 5.2 mm (0.203 in) and greater in thickness but not greater than 150 mm (6 in) wide, and flats greater than 5.8 mm (0.229 in) thick and over 150 mm (6 in) to 204 mm (8 in) wide.This document previously covered plates, structural shapes, and bar size shapes of Grades 290A, 345A, 415A, 450A, 345W, 345F, 415F, 485F, and 550F as well as bars of Grades 290A, 415A, and 345W. These products are no longer covered; requirements for these products and grades can be found in ASTM Specifications as follows in Table 1:
Rationale: This SAE Recommended Practice covers two levels of high strength structural low-alloy steel bars having minimum Yield Points of 345 MPa (50 ksi) and 450 MPa (65 ksi).The two strength levels are 345 and 450 MPa or 50 and 65 ksi minimum yield point. Different chemical compositions are used to achieve the specified mechanical properties. In some cases there are significant differences in chemical composition for the same strength level, depending on the fabricating requirements.It should be noted that although the mechanical properties for a steel grade sourced from different suppliers may be the same, the chemical composition may vary significantly. The fabricator should be aware that certain compositional differences may effect the forming, welding, and/or service requirements of the material. It is therefore recommended that the fabricator consult with the producer to understand the effect of chemical composition.The products within the scope of this document include bars of the following types and sizes:Rounds, squares, and hexagons of all sizes (cut length only), flats 5.2 mm (0.203 in) and greater in thickness but not greater than 150 mm (6 in) wide, and flats greater than 5.8 mm (0.229 in) thick and over 150 mm (6 in) to 204 mm (8 in) wide.This document previously covered plates, structural shapes, and bar size shapes of Grades 290A, 345A, 415A, 450A, 345W, 345F, 415F, 485F, and 550F as well as bars of Grades 290A, 415A, and 345W. These products are no longer covered; requirements for these products and grades can be found in ASTM Specifications as follows in Table 1:

© 2009-2024 标准资料网 版权所有，并保留所有权利。

北京智聚科技有限公司 Tel: 010-67123753 E-mail: kefu@infoeach.com

京ICP备14017250号-1